| Keyword |
Part Number |
Description |
|---|
| Accessory | CH971-62824 | Adhesive backed ruler - English metric ruler - 2.5m (98-inches) long and can be cut down for the 1.6m (64-inches) size - This is the ruler located with the N-up alignment pins |
| Accessory | CH971-63114 | High Density Polyethylene (HDPE) funnel - 32Oz capacity - Facilitates emptying ShopVac waste ink into waste ink bottle |
| Accessory Kit | CH971-56881 | Accessory kit for the support tables - Includes all the fasteners, casters, etc needed to assemble two tables - For use with the Scitex FB910/FB950 printers |
| Actuator | CQ114-67094 | 75mm stroke actuator assembly - This is the actuator and all associated bracketry and hardware plus the lift encoder reader and strip - Used for the input and output media hold-down rollers and the alignment bar - For the Scitex FB500/FB700/FB950 printers |
| Actuator | CH109-67003 | Lift motor (actuator) - Used for all up/down component movement in the printer - This motor is used in nine locations on the printer |
| Actuator | CQ114-67068 | Lifting actuator for the rail - For the Scitex FB500/FB700 printer |
| Bar | CQ115-67012 | Anti-static ionizer bar - For the Scitex FB700 printers |
| Bar | CH971-57513 | Bar media guide - This bar is lowered down to stop and square the media |
| Bar | CH154-50002 | Ionizer bar - Includes the bar with cable only - Attaches to the input side of the rail - For use with the Scitex FB950 printer |
| Bar | CH971-91490 | Y-axis alignment bar - Includes fine-thread screws for adjusting the Y-axis alignment of the printheads - Located in front of the printheads |
| Belt | CH971-90710 | Carriage drive timing belt - Located between the carriage drive motor and the carriage drive shaft |
| Belt | CH971-91530 | Drive belt - Used for the service station wiper motion |
| Belt | CH154-67003 | Main carriage drive belt (Blue) - For use with Scitex FB950 printers |
| Belt | CH971-91462 | Media belt - Includes all the support pieces and accessories used to change the belt - For use with the Scitex FB950/FB910 printers |
| Blower | CH971-91400 | Belt vacuum blower assembly - Includes one blower - Used to suck down media to belt - For the FB500/FB700/FB950/FB910 |
| Bottle | CH154-67015 | Flush bottle - Squeeze bottle with label for UV flush |
| Bottle | CH154-67014 | Waste ink bottle - One gallon bottle with warning label for collection of UV liquid wastes |
| Box | CJ848A | Electronics assembly (ebox assembly) - For use with the Scitex FB950 |
| Bracket | CH971-57219 | Carriage drive bracket - For use with Designjet H series and Scitex FB910/FB950 printers |
| Bracket | CH108-60011 | L-bracket - Located on the input, service end of the printer - Holds the supply roll and inactive foam rollers |
| Bracket | CH108-60010 | L-bracket - Located on the input, user end of the printer - Holds the supply roll and inactive foam rollers |
| Bracket | CH108-60009 | L-bracket - Located on the output, service end of the printer |
| Bracket | CH108-60008 | L-bracket and internal mechanical - Located on the on the output, user end of the printer - Includes the parts that transfer take-up motor power to the take-up spool (does not include the motor/switch assembly, the takeup drive belt, or the belt cover) |
| Bracket | CH971-57259 | Service-end bracket - Supports the lift and press rollers in the roll-to-roll option |
| Brush | CH971-62665 | Brass wire brush - Used to clean the ionizer bar |
| Brush | CQ114-67180 | Ionizer brush - Used to clean the points on the anti-static ionizer bar |
| Bumper | CH971-62205 | Polyurethane rubber bumper - 7/16-inch diameter x 13/64-inch thick round, adhesive-backed bumper - Used on some platforms on the rail at the carriage home, or as a spacer on the headboard-end of the LVDS cable (on Scitex FB500/FB700 printers only) |
| Button | CH971-91398 | Emergency stop button - For use with Scitex FB950/FB910 printers |
| Cable | CH971-50116 | Cable - Goes from the AC filter to the power distribution board |
| Cable | CH971-57465 | Cable - Goes from the external power receptacle for the ionizer power supply to the I/O board and power distribution board |
| Cable | CH971-57303 | Cable - Goes from the headboard to the air valve assembly |
| Cable | CH971-50028 | Cable - Goes from the three pin sabre connector on the AC distribution board to an AC receptacle |
| Cable | CH971-50284 | Cable - Goes from the UV power supply to the external connector for the UV lamp cable found on the top side of the electronics box |
| Cable | CH971-52323 | Cable - Used to connect the printer directly to a print server - For use without a hub |
| Cable | CH971-50364 | Cable assembly - 2-wire cable - Goes from the UV power supply to the cable harness from the I/O board |
| Cable | CH971-50286 | Cable assembly - 2-wire cable - Ties in to the power cable for the UV lamp cable receptacle on the exterior of the electronics box |
| Cable | CH971-50289 | Cable assembly - 2-wire cable - Ties in to the power cable for the UV lamp cable receptacle on the exterior of the electronics box |
| Cable | CH971-50014 | Cable assembly - Braided ribbon cable from OHS board to I/O board - For the Scitex FB500/FB700/FB910/FB950 printers |
| Cable | CH971-50148 | Cable assembly - Cable between the headboard and the UV lamp - For the Scitex FB950 and the Designjet H-Series |
| Cable | CH971-50322 | Cable assembly - Goes from the headboard to the carriage home sensor |
| Cable | CH971-55682 | Cable assembly - Goes from the I/O board to the motor control board |
| Cable | CH971-50404 | Cable assembly - Goes from the lower HDBD connector to the front carriage fans and color sensor fan |
| Cable | CH971-50299 | Cable assembly - Goes from the power distribution board to the external receptacle for take-up motor power |
| Cable | CH971-50163 | Cable harness - Goes from the OHS board to the ink pumps |
| Cable | CH971-50316 | Camera fans cable - Goes from the upper HDBD connector to the rear carriage fans |
| Cable | CH971-50300 | Internal ebox cable - Goes from the AC distribution board to the UVPS and AC relay - Has a 4-pin molex sabre connector for the AC distribution board connection |
| Cable | CH971-50354 | Internal ebox cable assembly - Cable that goes from the I/O board J28 to AC relays, cooling fans, main power switch, foot pedal, and UV cable-present sensor |
| Cable | CQ114-67128 | LVDS data cable - For use with the Scitex FB950 printer |
| Cable | CQ114-67051 | Serial data cable - Touch-sensitive data transmission cable - Located between the LCD control panel and the I/O board |
| Cable | CH154-67009 | UV lamp power cable - Cable goes from the electronics assembly to one lamp - For use with Scitex FB500/FB700/FB950 |
| Cable | CQ114-67052 | VGA cable - Located between the LCD control panel and the motherboard - For the video display |
| Camera | CH971-91605 | Camera assembly - For use with Scitex FB950 and the Designjet H-series |
| Cap | CH971-91589 | Printhead cap - Used to cap a printhead port or similar luer fitting location |
| Cap | CH971-91590 | Tube cap - Used to cap the end of the luer fitting that normally connects to the ink tube |
| Carriage | CQ114-67109 | Carriage drive assembly - Includes bracket, motor, drive shaft, timing belt, and all related fasteners - For the Scitex FB500/FB700 printer |
| Carriage | CH971-91502 | Carriage drive assembly with bracket - For use with Scitex FB950/FB950 and Designjet H series |
| Carriage | CH971-91497 | Carriage headboard assembly - For use with the Designjet H-Series and Scitex FB950 printer |
| Clamp | CH971-57723 | Clamps - Does not in include the fastener - Secures the main (Blue) drive belt to the (Black) clips in the carriage |
| Clip | CH971-91001 | Clip - Connected to the trolley and provides attachment points for the carriage drive belt on both ends |
| Clip | CH154-67045 | Clip assembly - Includes one unit, does not include the taller luer cap required for use with the clamp - Used on the printhead ink U-tubes - For use with Designjet H-series and Scitex FB950 |
| Collar | 1500-1274 | Internal clamping collar - 25mm diameter - Used on the ends of the media drive idle roller shaft - For the Scitex FB910/FB950/FB500/FB700 printers |
| Collar | CH971-91264 | Spool-holding collar - Attaches to the stand on the left side take-up and supply postions (when facing front of printer) |
| Collar | CH971-91265 | Spool-holding collar - attaches to the stand on the right side take-up and supply postions (when facing front of printer) |
| Connector | CH971-57327 | Complete ink tube/filter/connectors assembly - Used with the ink boxes - For use with Scitex FB950/FB500/FB700 and Designjet H (CS 5400uv) printers |
| Coupler | CH971-91634 | Off-Head Supply (OHS) ink coupler - Includes one coupling and the nut used to secure it on the printer - This is the quick-disconnect attachment for the ink boxes and receives the connector from the inkbox pigtail |
| Display | CH154-60033 | LCD display assembly - For use with Scitex FB950 printers only |
| Drive | CH154-67038 | Hard disk drive (HDD) - Used in the electronics assembly - For use with the Scitex FB950 printer |
| Enclosure | CH154-00013 | Belt/roller enclosure - Located on the output-side of the user-end |
| Enclosure | CH971-57586 | Belt/roller enclosure - Located on the service-end (input-side) |
| Enclosure | CH971-57585 | Belt/roller enclosure - Located on the user-end (input-side) |
| Enclosure | CJ856A | Carriage cover enclosure - Includes the fans - For use with the Scitex FB950 printer |
| Enclosure | CH971-57580 | Central top enclosure assembly - Includes all fans, windows, light blocking skirt, and required fasteners - Located on the output side of the printer (top cover that can be opened) |
| Enclosure | CH971-57557 | Central top enclosure assembly - Includes the window material and fasteners - Located on the input side of the printer |
| Enclosure | CH971-57559 | Full enclosure skins - For use on the user side of the printer - For use with the Scitex FB950 printer |
| Enclosure | CH154-67012 | Window enclosure - Includes pushnuts - Replacement UV-blocking windows used only on the center output-side door - For the Scitex FB500/FB700/FB950 |
| Encoder | CH971-90708 | Encoder reader assembly - Located on the back of the carriage assembly |
| Encoder | CH154-67005 | Encoder strip actuator assembly - Includes bracket - Used in all lifting assemblies and service station - For the Scitex FB950 printer |
| Encoder | CH154-67040 | High-resolution on-shaft encoder - Used for media drive motion - For use with the Scitex FB950 printer |
| Encoder | CH971-91407 | Media drive encoder - Attaches to the belt drive motor on the service end of the printer - Does not include the high-resolution encoder - For the Scitex FB500/FB700/FB950/FB910 |
| Encoder | CH971-91425 | Mylar encoder strip and foam tape - It is long enough for a 2.5m (98-inch) printer and can be trimmed down for smaller printers - Part requires you to reuse the existing aluminum bar from the old strip |
| End Cap | CH971-57560 | End cap sheet metal - Located on the service end of the printer - For use with the Scitex FB950 printer |
| Fan | CH154-67010 | Cooling fan - Used on the carriage (all four locations) and the Designjet H image sensor - For use with Scitex FB950 printers only |
| Fan | CH971-91513 | Fan assembly - Cools the electronics box in the printer |
| Fan | CH971-91599 | Fan assembly - Located on the top enclosure and end enclosures - For the Scitex FB500/FB700, also the Designjet H-Series |
| Fan | CH971-91596 | UV lamp housing cooling fan - For the Scitex FB500/FB700/FB950, and Designjet H-series printers |
| Filter | CH971-60050 | AC filter - Located inside the electronics assemblies - For use with Scitex FB910/FB950 printers |
| Filter | CH971-91504 | Ink filter - 1.74-inch diameter - Can be used with any ink color - This filter is used in the OHS area of the printer - For use with Scitex FB950 and Designjet H-Series |
| Filter | CH108-60004 | Large cylindrical air filter - Located on the exterior of the vacuum assembly |
| Filter | CH971-91644 | Shop Vac filter (Gray) - Internal filter material for the UL |
| Filter | CH104-67020 | Tube/filter/fitting assembly - Used between the printhead and the air manifold |
| Glass Assembly | CH971-91594 | Quartz lamp glass - Inserts below the left or right lamp housing - For the FB500/FB700/FB950, also the Designjet H-Series |
| Guard | CH971-57605 | Finger guard - Includes a white media alignment fence on engines without the roll-to-roll option - Located on the user-end (input-side) |
| Guard | CH971-57318 | Finger guard - Located on the service-end (input-side) over the belt on engines without the roll-to-roll option |
| Guard | CH971-57691 | Finger guard with media alignment fence (White) - Located on the user-end (input-side) engines without the roll-to-roll option |
| Guard | CH154-00020 | Media belt edge guard - Located on the user side - For use with the Scitex FB950 printer |
| Guard | CH154-00021 | Media belt edge guard - Located on the service side - For use with the Scitex FB950 printer |
| Hardware | CJ862A | Cabling loom (conduit and cables) - Used between the electronics assembly and devices in the user-end removable enclosure |
| Hardware | CJ860A | Cabling loom (conduit and cables) - Used between the electronics assembly and devices on the service end of the printer |
| Hardware | CJ861A | Cabling loom (conduit and cables) - Used between the electronics assembly and devices on the user end of the printer (excluding devices in the user-end removable enclosure) |
| Hardware | CH976-00149 | Check valve assembly (Black) - Used in the Off-Head Supply (OHS) - Color-coded for Black |
| Hardware | CH976-00152 | Check valve assembly (Blue) - Used in the Off-Head Supply (OHS) - Color-coded for Cyan |
| Hardware | CH976-00151 | Check valve assembly (Green) - Used in the Off-Head Supply (OHS) - Color-coded for Light Magenta |
| Hardware | CH976-00150 | Check valve assembly (Red) - Used in the Off-Head Supply (OHS) - Color-coded for Magenta |
| Hardware | CH976-00148 | Check valve assembly (White) - Used in the Off-Head Supply (OHS) - Color-coded for Light Cyan |
| Hardware | CH976-00153 | Check valve assembly (Yellow) - Used in the Off-Head Supply (OHS) - Color-coded for Yellow |
| Hardware | CH154-67001 | Complete trolley assembly - Includes upper and lower plates - For use with Scitex FB950 printers |
| Hardware | CH154-60013 | Ink float sub-assembly - Screws to the service station bucket/separator |
| Hardware | CH971-91544 | Ink pump - Includes the tubing, fitting, and torx fasteners for installation |
| Hardware | CH154-67013 | Light-blocking skirt - Used for the main cover - For use with Scitex FB950 printer |
| Hardware | CH971-62547 | Luer fitting (White) - 1/8-inch, male-taper - Used on the ink tubing |
| Hardware | CH971-62550 | Luer fitting (White) - 3/32-inch, male-taper - Used on the ink tubing |
| Hardware | CH971-91491 | Manifold assembly - Includes six valves that mounts on the rear of the carriage above the trolley |
| Hardware | CH971-91531 | Shop Vac vacuum - Input voltage 220VAC - Used for the service station |
| Hardware | CH154-67043 | ShopVac vacuum - 8-liter capacity - Compatible with all vintages of the Scitex FB950 printer - When installing this part on some vintages, a power cable (included) must be replaced |
| Hardware | CH971-91598 | ShopVac vacuum - Input voltage 110VAC (USA) |
| Hardware | CH971-91414 | Side alignment fence - Attached to belt assembly |
| Hardware | CH154-67034 | Track assembly - For use with the Scitex FB950 printer |
| Hardware Kit | CH154-67044 | Hardware kit - Includes 12 clip assemblies and 12 taller luer caps - For use with the Designjet H-series and Scitex FB950 |
| Hardware Kit | CH154-67016 | Hardware kit - Includes the hose, spigot, and related hardware from service station basin to printer enclosure |
| Hardware Kit | CH154-67042 | Hardware kit - This is the one-time field modification kit to install a complete set of six air tube assemblies with ink-blocking filter onto the carriage - For use with the Scitex FB950 printer |
| Hardware Kit | CH971-91602 | Ink line and fittings kit - Includes 24-inch UV ink tubing and an assortment of color-coded luer fittings |
| Holder | CH154-60008 | Carriage restraint - Includes all components - Used for shipping |
| Housing | CQ115-67047 | Service-side lamp housing - Does not include bulb - For the Scitex FB700/FB950 |
| Housing | CQ115-67048 | User-side lamp housing - Does not include bulb - For the Scitex FB700/FB950 |
| Idler | CH971-91595 | Idler assembly - Located on service-end of the rail - For use with Scitex FB910/FB950 and the Designjet H-series |
| Lamp | CH154-67091 | UV bulb/lamp - For use with Designjet H-Series and Scitex FB950/FB500/FB700 printers |
| Lubricant | CH109-67002 | Oil-saturated cloth - Used for lubricating the carriage rail - For use with Scitex FB500/700/FB950, and H-Series printers |
| Maintenance Kit | CH971-90854 | Grease kit - Used to lubricate gritroll bearings, media drive worm gear, and up/down threads of the media hold-down roller |
| Motor | CH971-90811 | Carriage drive motor - For Scitex printers |
| Motor | CH154-67008 | Media drive motor/reducer assembly - For the Scitex FB950/FB500/FB700 printer |
| Motor | CH971-91533 | Service station wiper motor - Moves the wiper head in the Y axis - For the Scitex FB500/FB700/FB950, also the Designjet H-Series |
| Motor | CH971-91561 | Takeup motor and switch assembly - Used for the roll-to-roll accessory - For the Scitex FB500/FB700/FB910/FB950 |
| Mount | CH971-62834 | Flush panel mount - Recessed plastic hand-hold as used in the enclosures - For the Scitex FB910/FB950/FB500/FB700 |
| Pad | CH971-91405 | Leveling pad - For Scitex FB500/FB700/FB950/FB910 printers |
| Pan | CH154-00004 | Light blocking pan - Located over the OHS area - For use with the Scitex FB950 printer |
| PC Board | CH154-67041 | Formatter - Software version 4.20 - For use with the Scitex FB950 printer |
| PC Board | CJ855A | I/O board - For use with the Scitex FB950 printer |
| PC Board | CH971-91542 | Main controller board - Used for the Off-Head Supply (OHS) - Has sockets for the profilers |
| PC Board | CH154-67035 | Motherboard assembly - For use with the Scitex FB950 printer |
| PC Board | CH971-91389 | Motor driver board (motor control board) - Located in the electronics assembly - For the Scitex FB500/FB700/FB91O/FB950 printers |
| PC Board | CH971-91450 | Power Distribution board - Regulates the 3-phase power going into the printer |
| Pin | CH971-91402 | Alignment pin assembly - These pins are used to set position of multiple sheets - For the Scitex FB500/FB700/FB950/FB910 |
| Plate | CH154-67002 | Upper trolley plate assembly - For use with Scitex FB950 printers only |
| Power Cord | CH109-50001 | 3-phase power cord - For use with plotters (Europe) |
| Power Cord | CQ114-67046 | Headboard power cord - Located in the track from the electronics assembly to the headboard - For use with the Scitex FB500/FB700/FB950 |
| Power Cord | CH971-56213 | Main AC power cord - For use with Scitex FB910/FB950 printers |
| Power Supply | CH971-90826 | ATX power supply - Output voltage 12VDC - Located in the main electronics box |
| Power Supply | CJ854A | Dual charge power supply - Output voltage 24/38VDC - For use with the Scitex FB950 printer |
| Power Supply | CH971-91618 | Ionizer power supply - For replacement of the Simco-branded ionizer-bar power supply only |
| Power Supply | CH971-60068 | Mini power supply (24VDC) - Powers the ink system vacuum pump only - For use with Scitex FB950 and Designjet H printers |
| Power Supply | CH154-67011 | UV power supply - For one channel of the lamp system - For use with Scitex FB950 printers |
| Power Supply Kit | CH971-91083 | Power supply and power plug adapter kit - Needed to implement the external auxiliary power source for IDS vacuum |
| Pressure Assembly | CH971-91543 | Vacuum pressure assembly |
| Pressure Assembly | CH104-67002 | Vacuum/pressure assembly - Pressure pump for the Ink Delivery System (IDS) - Located on the OHS assembly |
| Printhead | CH971-91493 | Master printhead - Does not include any thermistors - Used on any location of the printer - For use with Scitex FB950 and any model of the Designjet H series |
| Reader | CH154-67006 | Encoder reader board - Does not include the metal bracket - This assembly is used on all of the lifting positions - For the Scitex FB950/FB500/FB700 printer |
| Receptacle | CH971-50021 | External AC-input receptacle (Blue) - Includes the cable from the receptacle to the AC filter |
| Regulator | CH971-91626 | Regulator - Used in the Vacuum Pressure (VP) assembly |
| Relay | CH971-91586 | AC relay - Located in the main electronics box |
| Reservoir | CH104-67001 | Printhead reservoir kit - For use when there is a reservoir leak, fitting problem, or other printhead issues, where jetting is not the problem - For use with any of the piezo-printhead engines |
| Reservoir | CH971-57266 | Vacuum reservoir - This is a portion of the ink system vacuum - For use with Designjet H series and Scitex FB950 printers |
| Roller | CH971-91603 | Bearing media roller |
| Roller | CH971-57296 | Foam-covered metal roller - Used in two places in the roll-feed supply system - For use with Scitex FB910/FB950 printers |
| Roller | CH154-20015 | Media drive roller - Located on the output side of the engine - For use with the Scitex FB950 printer |
| Roller | CH154-20016 | Media drive roller - Located on the output side of the engine - For use with the Scitex FB950 printer |
| Roller | CH971-57520 | Media hold-down roller assembly - Located on both input or output sides - For use with the Scitex FB950 printer |
| See Description | CH971-91089 | Media spool collet - 3-inch in size - Can be hand tightened and loosened around the steel media spool |
| See Description | CH971-91344 | Restrictor - For use with all vacuum/pressure assemblies |
| Sensor | CH971-62685 | Bracket height adjustment sensor - Mounting bracket for the alignment sensor that confirms that the media is straight before the pinch roller goes down |
| Sensor | CH971-60085 | Carriage home sensor - For use with Scitex FB950 printer |
| Sensor | CH971-91406 | Media thickness sensor assembly - Calibrated in the factory - For the Scitex FB950/FB910/FB500/FB700 printer |
| Sensor | CQ114-67023 | Optical media-out detection sensor - Located on the input side of the printer - Two are used on the printer, one at center and one at the user end - For the Scitex FB500/FB700/FB950 printer |
| Sensor | CH971-91028 | Service station sensor - This is the home sensor for the wipers |
| Service Station | CJ857A | Service station assembly - For use with the Scitex FB950 printer |
| Shaft | CQ114-67110 | Carriage drive shaft - Shaft is knurled to prevent pulley from slipping on the shaft - For the Scitex FB500/FB700/FB910/FB950 printer |
| Shipping Material/Carton | CH154-67033 | Repacking kit - Materials to repack plotter - For use with Scitex FB950 printers |
| Slide | CH154-67031 | Vertical slide - Located on the service station - If broken, this can be replaced alone without requiring replacement of the entire service station assembly |
| Spindle | CH971-91558 | Media spool - Does not inlcude collets - For use with 98-inch printers |
| Spindle | CH971-91258 | Media spool - Includes two 3-inch collets - For use with 98-inch printers |
| Spring | CH971-63071 | Gas springs - Used to hold open the main cover on - For use with the Scitex FB950 printer |
| Support | CH971-56880 | Media support table - For use with the Scitex FB910/FB950 |
| Switch | CH971-91576 | Door switch - Used ont the cover-open detect - For use with Designjet H-series printers |
| Switch | CH971-91469 | On/Off switch - Located on the electronics assembly - For the Scitex FB500/FB700/FB950/FB910 printers |
| Switch | CH154-67037 | Replacement foot switch - Orange safety hood not included - For the Scitex FB700/FB950/FB910 and H-Series |
| Switch | CH971-91444 | Switch - Configures the power distribution board for the type of 3-phase power used at the site - This switch must be set correctly before power is applied to the printer, or serious damage can occur to the printer |
| Tape | CQ115-67051 | Foam tape - 175cm (69-inch) long - Located on top of the rail that cushions the track assembly (Igus) - This length is for any 2.5m (98-inch) printer, but may be cut down to shorter lengths for use on other machines |
| Tensioner | CH971-91562 | Supply tensioner - Used on the user-input bracket, for use with the supply and take-up system - For use with Scitex FB910/FB950 printers |
| Thermistor | CH971-91492 | Thermistors kit - Includes two ink and one air temperature thermistor (they have been calibrated together and should be replaced together) |
| Tool | CH971-91572 | Belt tension tool kit - Fixture used to measure tension on the media belt - Requires a dial indicator (not included) - For the Scitex FB500/FB700/FB950/FB910 |
| Tool | CH971-57693 | Custom tool - Assists removing and installing the main drive belt connection to the carriage |
| Tool | CH971-55984 | Head height gauge tool - This go/no-go gauge is used to set the printhead height to 0.085-inches above the surface of the media |
| Tool | CH971-91631 | Service tools kit - Kit includes the head height gauge, squeeze bottle (for flush), lint-free cloths, luer caps, and the carriage belt - For use with Scitex FB950 and the Designjet H-series |
| Transformer | CH971-15183 | Step-down transformer (220VAC to 110VAC) - Used with the 110VAC ShopVac |
| Tray | CJ859A | Input/output vacuum fan tray - Includes the fans - Used for both the input and output zones of the vacuum table - For use with the Scitex FB950 printer |
| Tray | CJ858A | Vacuum fan tray - Includes the fans - Used for the pre-print (center) zone of the vacuum table - For use with the Scitex FB950 printer |
| Tube | CQ114-67221 | Bucket tube - 10.90-inches (27.68 cm) length hose - Includes hose clamps for attachment - Located in the service station basin (bucket) between the wiper and the baffle - For use with Scitex FB500/FB700/FB950 printers |
| Tube | CH154-67024 | Ink system pressure tube - Runs through the track assembly - For use with FB500/FB700/FB950 |
| Tube | CH154-67023 | Ink system vacuum tube - Runs through the track assembly - For use with Scitex FB500/FB700/FB950 printers |
| Tube | CH154-67018 | Long opaque tube (Black) - For ink that runs through the track assembly - Luer fittings color-coded for the black ink channel |
| Tube | CH154-67021 | Long opaque tube (Blue) - For ink that runs through the track assembly - Luer fittings are color-coded for the cyan ink channel |
| Tube | CH154-67020 | Long opaque tube (Green) - For ink that runs through the track assembly - Luer fittings are color-coded for the light magenta ink channel |
| Tube | CH154-67019 | Long opaque tube (Red) - For ink that runs through the track assembly - Luer fittings are color-coded for the magenta ink channel |
| Tube | CH154-67017 | Long opaque tube (White) - For ink that runs through the track assembly - Luer fittings are color-coded for the light cyan ink channel |
| Tube | CH154-67022 | Long opaque tube (Yellow) - For ink that runs through the track assembly - Luer fittings are color-coded for the yellow ink channel |
| Tube | CH971-91499 | Short UV ink tube - Connects to the printhead with a luer fitting and to the ink track tube with multi-colored luer fittings |
| Tube | CH971-91227 | U-tube - For use with ink between two printheads of a color |
| Tube | CH154-67004 | U-tube assembly - For air connection between any two UV printheads |
| Wiper | CH154-67030 | Wiper blade - For use with the Scitex FB950 printer - This is a different material than the H-Series wiper |